• <tbody id="hgpi9"><pre id="hgpi9"></pre></tbody>
      1. <tbody id="hgpi9"></tbody>

        1. <em id="hgpi9"><acronym id="hgpi9"><u id="hgpi9"></u></acronym></em>

          1. 泰安揚帆數控科技有限公司為您提供山東焊接專機等相關信息發布和資訊展示,敬請關注!
            咨詢服務熱線:
            0538-5358300

            新聞資訊

            推薦產品

            行業新聞

            使用焊割設備過程中的注意事項!

            來源:http://www.leblogdejc.com/  發布時間:2021-10-15 瀏覽次數:

            一般在地下室、隧道、金屬容器內以及比較密閉的場所進行焊割作業時,由于空氣不流通,進出不方便,光線不充足,場地不寬暢,活動不方便等特殊因素,在焊、割作業中容易發生事故,也不容易進行搶救。因此,必須嚴格采取下列安全措施。

            Generally, when welding and cutting operations are carried out in basements, tunnels, metal containers and relatively closed places, due to special factors such as poor air circulation, inconvenient access, insufficient light, poor site and inconvenient activities, accidents are easy to occur in welding and cutting operations and it is not easy to rescue. Therefore, the following safety measures must be strictly taken.
            (1)作業前必須認真仔細地對作業場所內外的情況調查清楚,要查清室外的建筑或其他結構對室內動火焊、割是否有影響,室內是否有易燃易爆物質,必要時應先對室內的氣體進行取樣分析,確認安全后,才能進入室內操作。
            (1) Before operation, the situation inside and outside the workplace must be carefully investigated. It is necessary to find out whether the outdoor buildings or other structures have an impact on indoor hot welding and cutting, and whether there are flammable and explosive substances in the room. If necessary, the indoor gas shall be sampled and analyzed to confirm safety before entering the room for operation.
            (2)乙炔發生器、氧氣瓶、電焊機均不準放在動火焊、割的室內。要仔細檢查氧-乙炔管道和焊、割炬是否漏氣,嚴防氧-乙炔氣體體積聚在室內而引起爆炸事故,暫停焊、割時要把氧-乙炔管道和焊、割炬拿出室外。并打開所有門窗或閥門,盡可能保持空氣流通,必要時要采取機械通風。
            (2) Acetylene generator, oxygen cylinder and electric welding machine are not allowed to be placed in the room of hot welding and cutting. Carefully check the oxygen acetylene pipeline and welding and cutting torch for gas leakage, and strictly prevent the explosion accident caused by the concentration of oxygen acetylene gas in the room. When welding and cutting are suspended, take the oxygen acetylene pipeline and welding and cutting torch out of the room. Open all doors, windows or valves to maintain air circulation as much as possible, and take mechanical ventilation if necessary.
            (3)用焊割設備進行電焊操作時,焊、割場所需保持干燥,嚴格檢查絕緣防護裝備是否符合安全要求。在金屬容器內作業時,焊工不準把頭、背等或未帶絕緣物的部位碰著金屬容器。照明設備一律采用低壓照明燈。
            (3) When using welding and cutting equipment for electric welding, the welding and cutting place shall be kept dry, and the insulation protection equipment shall be strictly checked to see whether it meets the safety requirements. When working in metal containers, welders are not allowed to touch their heads, backs, etc. or parts without insulation against metal containers. All lighting equipment shall adopt low-voltage lamps.
            (4)禁止把氧氣通入室內用作調節操作場所的空氣
            (4) It is forbidden to introduce oxygen into the room to regulate the air in the operation place

            上一篇:關于焊接夾具中的定位器的介紹!
            下一篇:焊接機器人對焊絲的質量要求是什么?

          2. <tbody id="hgpi9"><pre id="hgpi9"></pre></tbody>
              1. <tbody id="hgpi9"></tbody>

                1. <em id="hgpi9"><acronym id="hgpi9"><u id="hgpi9"></u></acronym></em>

                  1. 绝对真实偷窥女子会所私密av_扒开双腿猛进入在线观看_曰韩欧美亚洲美日更新在线_日本丰满大屁股少妇